• Warn Winch Vr8 Installation Guide
• Software Installation Manual
• Installation Guide

View and Download Bosch ICP-VR8488 user manual online. Intruder Alarm System. ICP-VR8488 Carbon Monoxide Alarm pdf manual download.

• Job Ross
• 3 years ago
• Views:

Transcription

1 Solution 144 Security Systems EN Installation Manual Security System

2 Solution 144 Installation Manual COPYRIGHT NOTICE Unless otherwise indicated, this publication is the copyright of Bosch Security Systems Pty Ltd ( Bosch ). All rights are reserved.you may download a single copy of this publication. By downloading the publication you agree that you will: (i) only use the publication for your own reference; (ii) not commercially exploit or charge any person for the use of the publication; and (iii) not modify the publication in any way without the prior written permission of Bosch. Except as specified above or where authorised by the Copyright Act 1968 (Cth), no part of this publication may be reproduced, transmitted, modified or stored in any form or by any means, without the prior written permission of Bosch. TRADEMARKS Throughout this document trademark names may have been used. Rather than put a trademark symbol in every occurrence of a trademark name, we state that we are using the names only in an editorial fashion and to the benefit of the trademark owner with no intention of infringement of the trademark. NOTICE OF LIABILITY While every effort has been taken the accuracy of this document, neither Bosch Security Systems Pty Ltd nor any of its official representatives shall have any liability to any person or entity with respect to any liability, loss or damage caused or alleged to be caused directly or indirectly by the information contained in this book. Should you find any error on inconsistency, please notify us accordingly. Warnings 1) This product must be installed by a qualified and licensed security installer. 2) This product may not perform as expected if installed incorrectly. 3) Some features of this product, including but not limited to Back to Base reporting, SMS and Reporting and Automatic Time and Date Adjustments require a working telephone line to operate and telephone communication service provider charges are applicable 4) Australian standard AS 2201 requires regular service by qualified and licensed security persons and regular user testing. Please consult your security alarm company for further details. 5) Incorrect programming of parameters can result in operation contrary to what may be desired. 6) Leave the mains adapter plugged in at all times. 7) Leave the telephone line plugged in at all times under normal conditions. 8) The Product Identification Label for this product which is supplied in the resistor pack, must be affixed to the outside of the enclosure during installation. N12138 Solution 144 Intrusion Control Panel TELEPERMIT N12138 Made In Australia Bosch Security Systems Pty Ltd reserves the right to make changes to features and specifications at any time without prior notification in the interest of ongoing product development and improvement. TELEPERMIT NOTE The grant of a Telepermit for a device in no way indicates Telecom acceptance of responsibility for the correct operation of that device under all operating conditions. This equipment shall not be used in any manner that could constitute a nuisance to other Telecom customers. Immediately disconnect this equipment should it become physically damaged, and arrange for its disposal or repair. The transmit level from this device is set as a fixed level and because of this there may be circumstances where the performance is less than optimal. Before reporting such occurrences as faults, please check the line with a standard telepermitted telephone. TELEPERMIT This Bosch Solution 144 CC600B Alarm System may be connected to the Telecom Network PTC 211 / 12 / 017 RN = 0.5 9) This equipment shall not be set up to make automatic calls to the Telecom 111 Emergency Service. ii Bosch Security Systems 05/11 BLCC600BI

3 CONTENTS Solution 144 Installation Manual Contents COPYRIGHT NOTICE.. II TRADEMARKS.. II NOTICE OF LIABILITY.. II TELEPERMIT NOTE.. II SECTION 1 OVERVIEW FEATURES OVERVIEW SECTION 2 INSTALLING THE HARDWARE ABOUT THE PANEL ENCLOSURES ENCLOSURE FIXING METHOD INSTALLING THE TAMPER SWITCH ENCLOSURE MODULE SPACES INSTALLING PANELS AND MODULES CONNECTING POWER TO THE PANEL CONNECTING THE BATTERY AC MAINS TRANSFORMER OPTION PANEL LED INDICATORS ABOUT THE KEYPAD STATUS ICONS / LED S KEYPAD TONES KEYPAD & READERS SETUP DIP SWITCH ADDRESS SELECT ROTARY SWITCH ADDRESS SELECT EOL RESISTOR COLOUR CODE SECTION 3 WIRING DIAGRAMS ZONE WIRING EOL RESISTOR COLOURS AND VALUES BOARD CONNECTORS TERMINAL DESCRIPTIONS LAN OVERVIEW LAN WIRING SYSTEM EARTHING TERMINATING THE LAN SECTION 4 PROGRAMMING OVERVIEW ENTERING PROGRAMMING MODE EXITING PROGRAMMING MODE COMMAND MENUS PROGRAMMING OPTION BIT MENUS NAVIGATING THE MENUS LIST OPTIONS ALPHA TEXT CLOCK PROGRAMMING TELEPHONE NUMBERS GETTING STARTED BACK TO BASE iii

4 iv Solution 144 Installation Manual Contents SERVICE MODE Turning Service Mode ON Turning Service Mode OFF DEFAULTING THE SYSTEM Hardware Default Software Default TRIGGERING A DURESS ALARM DOMESTIC TEMPLATE DEFAULTS DIRECT LINK PROGRAMMING ZONE ARRAY OUTPUT ARRAY DOOR ARRAY TESTING THE SYSTEM BASIC REPORTING REFERENCE DTMF CONTROL FUNCTIONS MENU REFERENCE TABLE BASIC SYSTEM OPERATION TURNING AN AREA ALL ON TURNING AN AREA PART ON / PART 2 ON TURNING AN AREA OFF SILENCING ALARMS AUTOMATIC ARMING REMOTE ARMING - QUICK ARM DURESS OR SILENT ALARMS SECTION 5 ACCESS PROGRAMMING USER DEFAULT TABLE USER PINS Erase User Change Own PIN Change Other PIN Add PIN Delete PIN View PIN USER TOKENS Add Token Delete Token Token Status Edit Token RF KEYFOBS Add Keyfob Delete Keyfob Test Keyfob USER PROPERTIES User Name Area Assignment User Options Master User Arm Only Can Bypass Auto Bypass Allowed Always Report Op/Cl UNDERSTANDING TIMEZONES User TimeZones TimeZone Access Example TimeZone Access Door Assignment User Expire Date PIN Length

5 Solution 144 Installation Manual Contents PIN Retry Count Installer PIN Access Route Access Options Add Fingerprint Delete Fingerprint Fingerprint Status SECTION 6 AREA PROGRAMMING AREA COMMANDS Area Status Turn Area On/Off Turn All Areas On Turn All Areas Off Move To Area Chime On/Off Chime Mode AREA PROPERTIES Area Name General Options Exit Time Restart Reset Alarm Memory Duress Allowed Fault ACK Required One Key Arming One Key Part On Link To Common Area One Key Part Off Input Options Non Sequential Pulse Count H/Over Senior Watch Output Options SPK Beeps Keyfob SPK Beeps Key/Sw SPK Strobe In Part On Alarm On PIN Retry Alarm Exit Error Alarm Key/Sw Tamper Reporting Options Report PIN Retry Report Exit Error Smart Lockout Cancel Report Op/Cl In Part On Op/Cl After Alarm Strobe Trigger Audible Burglary Silent Burglary Fire Alarm Keyfob On/Off Keyswitch On/Off Hr Alarm Part Mode 1 Name Part Mode 2 Name Auto Arming AREA REPORTING Account Dest Account Dest Open Close Route AREAS TIMERS Exit Time Entry Time Entry Time v

6 Solution 144 Installation Manual Contents Part Entry Time Auto Arm Pre-Alert Senior Watch Time AREA TESTING Area Watch User Test Interval Service Interval Test Options User Test Required Walk Test Report Walk Test 24Hr Walk Test Fire SECTION 7 INPUT PROGRAMMING ZONE ASSIGNMENTS INPUT COMMANDS Zone Status Zone Array Bypass Zones Set Chime Zones Set Part 2 Zones Smoke Sensor Reset ZONE PROPERTIES Zone Name ZONE DEFAULT TABLE Zone Type Not Used Burglary Delay Burglary Delay Burglary Instant Burg Inst No Exit Burglary Handover Burglary 24Hr Tamper 24Hr Hold Up 24Hr Medical 24Hr Panic 24Hr Fire 24Hr Keyswitch Zone Display Only Non Burglary 24Hr Area Assignment Pulse Count Pulse Count Time UNDERSTANDING ACCESS GROUPS Users Outputs Reader Access Group Door Access Group Example Door Assignment Report Route Report Options Lockout Dialler Report Alarm Report Troubles Report Bypass Report Restores Delay Reporting Zone Options Lockout Siren Silent Alarm Inverted Seal vi

7 Solution 144 Installation Manual Contents Bypass Allowed Sensor Watch Armed In Part On No EOL Required Test On Exit ADDING RF SENSORS Add RF Device Delete RF Device Test RF Device GLOBAL INPUT OPTIONS EOL Value Keyswitch Options Input Options Tamper On Short Response Time 500msec Keyswitch Open Close Alarm On Tamper Input Type Tamper Options Display Cabinet Tpr Report Cabinet Tpr Audible Cabinet Tpr Display Expander Tpr Report Expander Tpr Audible Expander Tpr INPUT TESTING Walk Test All Zones Walk Test A Zone Sensor Watch Time SECTION 8 OUTPUT PROGRAMMING OUTPUT COMMANDS Output Status Turn Output On/Off Output Array Door Status Door Array Door Override OUTPUT PROPERTIES Output Name Event Type Battery Trouble AC Trouble Telco Line Fail Comm Fail rd Dial Attempt Dest Reporting Reserved Dest Kiss Off User Keyfob Func User Keyfob Func Dialler Disabled Output Device Missing Output Trouble Panel On Line Incoming Call System Trouble Box Tamper Zone Trouble Zone Mirror Zone Alarm Area Disarmed vii

8 Solution 144 Installation Manual Contents 22 Area Part Or All On Area All On Area Part On Area Part 2 On Entry Timing Exit Timing End Of Exit Time Chime On Chime Zone Trigger Auto Arm Pre Alert Ready To Arm All On Ready To Part Arm Ready To Part 2 Arm Close Sent OK External Audible Internal Audible Any Zone Alarm Fire Alarm Burglary Alarm Silent Alarm Duress Alarm Keypad Medical Keypad Fire Keypad Panic Device Tamper Access Denied Strobe Smoke Sensor GND Sensor Watch Senior Watch Exit Error Keyfob Function Keyfob Function Output In PreDelay Follow PIN Code Part Entry Time TimeZones Temperature Hi/Lo Door Door Open Too Long CLI Trigger GSM Signal Lost GPRS Failure Ethernet Fail Event Assignment Output Polarity Open To Low Open To Low + Pre Open Latching Low Open Pulsing Low Open 1 Shot Low Shot Low+Retrigger Shot Low + Reset Low To Open Low To Open + Pre Low Latching Open Low Pulsing Open Low 1 Shot Open Shot Open+Retrigger Shot Open + Reset Speaker Output Toggle TIMED OUTPUTS Time Parameter One Shot Mode viii

9 Solution 144 Installation Manual Contents Pulsing Mode Output Options Guest Control Monitor Overload Monitor Device Fail Alarm On Device Fail Block If All On Show Status On Keypad Macro Group Reserved DOOR CONTROL Door Name Unlock TimeZone Door Options Hold Off If Area Armed Hold Off Auto Unlock Report Door Forced Alarm Door Forced OUTPUT TESTING External Siren Test Internal Siren Test Strobe Test Fire Siren Test OUTPUT EVENT TYPE TABLE OUTPUT ASSIGNMENTS OUTPUT DEFAULT TABLE SECTION 9 COMMS PROGRAMMING COMMS PROGRAMMING COMMANDS Call/Answer RAS Call Forward On/Off Check Web System Log Start Direct Link Voice Setup Register Customer Comms > Commands > Register Installer PHONE NUMBER PROGRAMMING Number Prefix Destination Destination Call Forward On Call Forward Off COMMS PROPERTIES Call Attempt Count Dialler Options Dialler Enabled Pulse Dialling Dial Tone Detect Busy Tone Detect Mirror Report WEB Extend H/S To 1min Abort Failed Reports Phone Line Options Display Line Fail Report Line Fail Alarm L/Fail If On Alarm L/Fail If Off Display On Line Country Set SMS Password Call Back Number ix

10 x Solution 144 Installation Manual Contents RAS Security PIN Log Threshold Ring Count RAS Options RAS Allowed Callback Verify Abort RAS On Alarm Answering Bypass Answer Only If Armed Tone Bypass Report RAS Sessions DTMF Options DTMF Arming DTMF Disarming DTMF User Functions DTMF Quick Arming Voice Access Code CLI Numbers User RAS PIN REPORTING OPTIONS TX Format Dest TX Format Dest Test Route System Route Emergency Route Swinger Dialler Burg Report Delay Fire Report Delay MYALARM IP Address IP Port MyAlarm Options Gateway Numbers Address Options Open Close Zones System Access SIA IP Prefix Account Number Account Prefix Receiver Prefix User Name/Password IP RAS Allowed IP RAS Only If Disarmed Report IP Session Report IP Lockout UDP Installer RAS UDP User RAS COMMS TESTING Send Test Report Test Report Time Test Report Period Test Report Options Test If No Other Rpt Test On Siren Reset Test Route Dial Number Test SECTION 10 DEVICE PROGRAMMING DEVICE COMMANDS Device Status LAN Secure

11 Solution 144 Installation Manual Contents LAN Scan LAN Watch Keypad Volume Keypad Contrast Keypad Backlight KEYPAD & READER OPTIONS Name Area Options All On Arming Allowed Part On Arming Allowed Disarming Allowed Single Button Control All User Areas Zero Exit Time PIN To Change Area Home Area Only Home Area General Options Enable Rear Tamper Report Temperature Installer Allowed Show Alarm When Armed Reader Area Control Reader Badging Enable Egress Input Log Egress Events Indicator Options Extinguish Greetings Display Temperature Display Area Icons Trouble Alert Beeps Entry Exit Warning Part Exit Warning Chime Tone Emergency Keys Audible Keypad Fire Report Keypad Fire Audible Kpad Medical Report Kpad Medical Audible Kpad Panic Report Keypad Panic Door Assignment Lockout Time RF RECEIVER OPTIONS Receiver Options Display RF Rcvr Trouble Alarm RF Rcvr Tamper Report RF Rcvr Tamper Alarm RF Rcvr Jamming Report RF Rcvr Jamming Alarm Rcvr Comm Fail Report Rcvr Comm Fail Supervision Time RF Device Options Display RF Tamper Report RF Tamper Report RF Low Battery Report Lost RF Devices Open Zone On Lost RF Audible Keyfob Panic Report Keyfob Panic Keyfob Func Part On Add RF Keypad Delete RF Keypad xi

12 Solution 144 Installation Manual Contents View RF Device ID SERIAL DEVICE OPTIONS Device Type Baud Rate Flow Control GSM/GPRS Status GSM/GPRS Options Auto Forward SMS Forward SMS To Mail CLI Trigger Table CLI Trigger Table SMS Control Display Faults Report Cable Lost Report IP Conflict Report Poll Fail SECTION 11 SYSTEM PROGRAMMING SYSTEM COMMANDS Panel Status System Trouble SYSTEM TROUBLE MESSAGES Power Missing AC Missing Battery Low Battery Missing Low Battery Box Tamper Temperature Alert Receiver Missing Case Tamper Receiver Jam Comms Fail Route Comms Fail Route Sensor Watch Alert Comms BUSS Trble Default PIN Trble Date & Time Cabinet Tamper Connection Trouble Overload Condition Zone Was In Alarm Telco Line Fail LAN+ Overload COMM+ Overload ACC+ Overload Service Required Memory Checksum Phone Line In Use Battery Trouble History Log Domestic Default Factory Default Template Default TimeZone Array Service Mode SYSTEM CLOCK Set Date And Time Summertime On Summertime Off Australian Daylight Savings Times Locale SYSTEM POWER OPTIONS xii

13 Solution 144 Installation Manual Contents AC Options Display AC Fail Report AC Fail Sync Clock to AC Random AC Reporting 2hr AC Fail After 1 Hour Display Clock Trouble Battery Options Display Battery Fail Report Battery Fail Battery Test On Arming OK To Arm Low Battery Fuse Options Display COMM+ O/Load Report COMM+ O/Load Display +12v O/Load Report +12v O/Load Display LAN O/Load Report LAN O/Load HORN SPEAKER OPTIONS Tone Speed Volume Siren Swinger TIMEZONES Name Time Day TimeZone Options Invert Logic Master Can Edit SYSTEM HOLIDAYS Holiday Name Start Stop Dates SYSTEM OPTIONS General Options Display LAN Fail Report LAN Fail Alarm On LAN Fail Cannot Change Own PIN Monitor Default PINs PIN Always Required Display Menu Numbers Area Options Area 1 Common First Open Last Close Reset Siren All Users Power Up As Down Fault ACK All Areas Delay Trouble Beeps Power Up Disarmed Keypad Idle Screen Keypad Hi/Lo Temp Installer Options Report Installer Report Prog Change Restrict Installer PIN Auto Exit Install 2hr Auto Exit Service 2hr Multi Tenant Mode Allow Defaulting Language Site Name xiii

It was no surprise that his sound soon opened up on 2008's Time: Line, a collaboration with rapper Kay. One of the dutch masters. He continued to evolve with Foreign Exchange's sophomore album, Leave It All Behind, which pointed towards '80s R&B. Sam Chennault. Dutch-born Nicolay emerged in the mid-'00s as the producer half of underground duo Foreign Exchange, which also included Little Brother lyricist Phonte. His work drew from the boom-bap revival that began with 9th Wonder, but was lusher in sound than that of most producers toiling in the niche, conveying a decidedly romantic streak.

14 Solution 144 Installation Manual Contents SYSTEM TESTING Walk Test All Zones Battery Test SECTION 12 PROGRAMMING EXAMPLES Opening a Door using a Single Digit Code Opening a Garage Door Using a 4 Button RF Keyfob Auto Arming an Area Operating an Output with a TimeZone Unlock a Door and Disarm Area 1 using a LAN Reader Unlock a Door and Arm/Disarm Area 1 using a LAN Reader Using CLI to establish Upload/Download Connection Sending SMS Alarm Reports SECTION 13 SPECIFICATIONS SECTION 14 INDEX xiv

15 SECTION 1 Overview FEATURES Listed below are the main features of the Solution 144 Control Panel. Individual Box Tamper Circuit Monitoring Report Via (Internet) Telephone Line Busy Tone Detect RAS Intelli-Connect CLI Caller Line Identification Daylight Savings Senior Watch System Maintenance Interval Reminder System Weekly Test Reminder Area Inactivity Interval Temporary PIN Dual Reporting Dual Redundant Reporting Alarm Report Abort/Cancel Options 8 Programmable Holiday Calendars 16 Programmable Door Assignments 8 On-board Zones (Exp To 144 Zones) Fire Alarm Verification 255 PIN Users 4 Supervised High Power Digital Outputs 1 Relay 2 Amp Form (C) Contact (Expandable to 32) Supervised Siren Driver Partitionable To 8 Areas Dialler Reports SIA, Contact ID, SMS and Formats Supervised LAN Keypads (Maximum 16 Keypads) Keyswitch Input 1000 History Event Memory EMI / Lightning Transient Protection Fully Menu Text Programmable Programmable Via Solution Link Software (Remote/Direct) Telephone Line Fail Monitor Time Executed Functions 60+ Output Event Types Exit Restart Expansion Module Supervision DTMF Tone Decoder Built In Remote Arming OVERVIEW Zones The Solution 144 control panel provides up to 144 separate zones of protection. Zone programming determines the panel s response to open/short and tamper conditions on the zone loop. Areas The control panel supports up to 8 separate areas. You can assign all zones to a single area, or you can assign each zone to a combination of different areas. You can arm and disarm the control panel by area, alternatively, you can arm and disarm several areas at the same time. Dialler The control panel has a built-in dialler to send reports to the receiving party (ie. Security company monitoring station, mobile phone etc). Keypads You can connect a maximum of 16 fully supervised keypads to the control panel. The available current affects the total number of keypads that you can connect without the need to provide additional power supplies. History Log The control panel can store up to 1000 history events from all 8 areas. All events are stored in the log, even if they are programmed not to report via the on-board dialler. You can view the control panel s history log via keypad, serial printer (optional), or by connection of a personal computer (direct/remote) using the Solution Link upload/ download software. Programming You can program the control panel either by a keypad or using a personal computer using the Solution Link upload/download software. 1-1

16 Solution-144 Installation Manual Overview This page left intentionally blank 1-2

17 SECTION 2 Installing the Hardware ABOUT THE PANEL ENCLOSURES The MW720B - Small Enclosure and MW730B - Large Enclosure have been designed to reduce installation time and improve aesthetics on larger installations where often multiple enclosures need to be located in close proximity to each other. A number of new features have been incorporated including a new style tamper bracket which can be easily installed before or after the enclosure is mounted to the wall, an anti tamper lid which insures the cabinet tamper triggers when the lid is removed, easier access for flexible and rigid conduits, additional 20mm cable entry knockouts and a new board mounting system using removable spring clips. The MW720B and MW730B enclosures include numerous holes, allowing the PCB mounting clips to be positioned in the most appropriate location for each installation. MW730B - Large Cabinet Use appropriate fasteners capable of handling a minimum of 12kg to fix the cabinet against a sturdy surface using the mounting holes provided. INSTALLING THE TAMPER SWITCH The tamper switch can be located on either the left or right hand side of the cabinet to suit the installation. Before installing the bracket, fit the tamper lead to the switch and then insert it into the bracket. Once the enclosure has been mounted to the wall, insert the tamper bracket into the rectangular hole in the top flange of the enclosure and then slide the base of the bracket toward the top until the tamper switch locates in the rear of the enclosure. Depress the tamper a few times with your finger to ensure smooth operation. i Note For ease, it is recomended that the PCB mounting clips are installed from the rear of the enclosure before mounting it to the wall. 3mm Philips Head Machine Screw Supplied Circuit Board Component Side Support Clip Press Fit Supplied Rear of Cabinet Figure 2: Tamper Bracket Installation Figure 1: PCB and Mounting Clip Installation Diagram ENCLOSURE FIXING METHOD MM720B - Small Enclosure Use appropriate fasteners capable of handling a minimum of 6kg to fix the cabinet against a sturdy surface using the mounting holes provided. ENCLOSURE MODULE SPACES The MW720 enclosure has space for 2 large modules or 4 small modules while the optional MW730 enclosure has space for up to 4 large modules or 8 small ones. The enclosures have been designed so that any combination of large and small units can be neatly mounted together on the wall. Each module is mounted to the enclosure using 4 or more clip in standoffs. The clips can be inserted from the rear of the enclosure before mounting it to the wall, or from the front of the enclosure after it has been mounted. Both methods should be performed using your finger tips to 2-1

18 Solution-144 Installation Manual Installing the Hardware prevent damage to the standoff. (Standoffs and screws are supplied with each module). All compatible add on modules will mount on these spaces. See below for list if modules which can be added to the control panel. Module Space Occupied Solution 144 Control Panel 2 Module Spaces CM704B Zone Expander 1 Module Space CM705B Universal Expander 2 Module Spaces CM710B Output Expander 1 Module Space CM720B LAN Power Supply 1 Module Space CM760B Real Time Clock 1 Module Space CM797B LAN Isolator Module 1 Module Space CM195B RF Receiver Expander 1 Module Space Table 1: Expansion Options Use the above table to help determine which size cabinet you will require for the job. On some export models, one module space will not be available as the mains transformer mounts in this location. INSTALLING PANELS AND MODULES Once the enclosure is secured in place, install the panels and modules onto the mounting clip using the supplied 3mm screws. Do not over tighten the screws. Figure 3: MW720B - Small Enclosure Details When fitting panels or large modules, you should use 5 mounting clips, one in each corner of the PCB and one in the middle of the PCB underneath the main terminal blocks. When mounting small modules, only 4 clips are required, 1 in each corner. Both enclosures are supplied with tamper switches, tamper leads, tamper brackets and a quantity of mounting clips and screws. If required, additional mounting clips and screws may be purchased in bags of 50 clips (10 packs x 5pcs). (P/N: MW890) Figure 4: PCB Mounting Clip The following example shows the MW720B -Small enclosure configured using 4 small modules. i Note The supplied mounting clips are designed to use the 3mm machine screws supplied with the enclosure. The use of self tapping screws will damage the clips. 2-2

19 Solution-144 Installation Manual Installing the Hardware 320 mm C C B A A A A B A A A A D CABLE ENTRY (REAR) A A A A A A A A 520 mm D CABLE ENTRY (REAR) A A A A A A A A D CABLE ENTRY (REAR) A A A A B A A A A B A = PCB Mounting Clip Holes B = Enclosure Mounting Holes C = Tamper Bracket Mounting Holes D = Earth Stud - 4mm Figure 6: MW730B - Large Enclosure Details The following examples show the MW730B - Large enclosure configured using 6 small modules and 1 large module. Figure 5: MW720B Configuration Examples 2-3

20 Solution-144 Installation Manual Installing the Hardware When installing large modules you should fit 5 mounting clips as shown. Clip 5 provides support under the main terminal block only. No screw is fitted. 1 MODULE SPACE 2 MODULE SPACE CABLE ENTRY (REAR) MODULE SPACE CONNECTING THE BATTERY The panel is supplied with a set of battey leads to suit the chosen enclosure. Connect the Red Battery lead to the Battery (+) terminal and the Black Battery lead to the Battery (-) terminal on the PCB. Once terminated onto the PCB connect the other end of the leads to the battery paying attention to the polarity. AC MAINS TRANSFORMER OPTION On models with an internal transformer, a permanent connection shall be made to the mains supply. See Figure 8. This must be completed by a suitably qualified electrician according to the applicable wiring standards and regulations. Next connect the transformer output wires (red) to the removable terminal block supplied and then connect it to the PCB. Always check the orientation of the terminal block with the PCB markings before connecting. CABLE ENTRY (REAR) i Note For permanently connected equipment, a readily accessable disconnect device shall be installed in a location near to the equipment. MODULE SPACE 4 MODULE SPACE 5 Transformer Output (Red Wires) Wiring must be carried out by a licensed electrician following applicable wiring standards CABLE ENTRY (REAR) 1 MODULE SPACE 6 2 MODULE SPACE 7 D A Transformer Input (Blue Wires) TRANSFORMER V A.C Hz 150mA FUSE 8AG - 250V 250mA MAX A 4 3 B A N L N FUSED L NEUTRAL EARTH ACTIVE A When installing small modules, you should fit 4 mounting clips as shown. C Figure 7: MW730 Configuration Examples CONNECTING POWER TO THE PANEL For normal operation, the panel requires both AC and DC power sources. The AC source can be provided either by an external adapter or by an internal transformer depending on the model and country of sale. When connecting using the AC adapter, feed the cable in to the enclosure and terminate the wires on the removable terminal block supplied before connection it to the PCB. If using a 3 wire Adaptor, then the earth wire should also be terminated onto the terminal block. Always check the orientation of the terminal block with the PCB markings before connecting it to the PCB. A = PCB Mounting Clip Holes B = Enclosure Mounting Holes C = Fused Terminal Block D = Transformer Figure 8: Internal Transformer Connection Diagram 2-4

21 PANEL LED INDICATORS The control panel PCB has two LED indicators (Dialler and Status LED s) which display the following information. Condition Meaning Off Offline On On Line (Dialling/Answered) Flashing Incoming Call Table 2: Dialler Indicator LED Condition Meaning Off Error On Error Flash Once Every 2 Seconds OK Flash Fast AC or Battery Trouble Table 3: Status Indicator LED i Note During factory defaulting the Status and Dialler LED indicators will flash alternatively for approximately 15 seconds. ABOUT THE KEYPAD The keypad has 20 keys that allow you to input instructions and navigate the programming menu s as required. Some keys have a secondary function which is activated by pressing and holding them down for two seconds. Each key is described below. Key to Description The numeric keys allow you to enter your user PIN when required. Use the [MENU] and the numeric keys to enter commands. The [MENU] key is also used to go back one level when navigating through menus or to exit a programming location without saving changes. The [ON] key allows you to turn an area or output on. To turn all areas on at the same time when the system has been partitioned, press and hold the [ON] key for two seconds. The [PART] key allows you to turn an area Part On. This key can also be used to bypass a zone or multiple zones when you press and hold for two seconds after you enter your PIN. The [OFF] key allows you to turn an area or output off. To turn all areas off at the same time when the system had been partitioned, press and hold the [OFF] key for two seconds after you enter your PIN. The [OK] key allows you to save any changes and exit the command. Solution-144 Installation Manual Installing the Hardware Key + for 2 sec + for 2 sec + for 2 sec Description The [MAIL] key allows you to read stored mail. This key can also be used to initiate a dialler test when you press and hold for two seconds. The [ ] key allows you to move the cursor left when programming text or telephone numbers. The [ ] key allows you to move the cursor right when programming text or telephone numbers. The [ ] key allows you to navigate through menus or to toggle characters when programming telephone numbers. The [ ] key allows you to navigate through menus or to toggle characters when programming telephone numbers. Pressing The [ ] key will display current trouble conditions when the area that the keypad is displaying is disarmed. Press and hold the [ ] and [ ] keys together for 2 seconds will initiate a panic emergency alarm to be triggered. If programmed, the sirens will sound and the monitoring station will be notified. Press and hold the [ ] and [ ] keys together for 2 seconds will initiate a fire emergency alarm to be triggered. If programmed, the sirens will sound and the monitoring station will be notified. Press and hold the [ ] and [ ] keys together for 2 seconds will initate a medical emergency alarm to be triggered. If programmed, the sirens will sound and the monitoring station will be notified. Table 4: Keypad Key Functions Figure 9: Keypad Emergency Alarm Trigger s 2-5

22 Solution-144 Installation Manual Installing the Hardware STATUS ICONS / LED S The following table lists the function of each of the ICON symbols and LED indicators on the keypad display. Icon Status Meaning The keypad can be programmed to display area icons (1 to 8) that allow users to easily identify which areas have been turned on or off without the need to toggle between areas (See MENU ). On Off Flashing Fast On Flashing Flashing Off On On Off Flashing On Off On Off On Off On Off Flash On Off The area is turned All On or Part On The area is turned Off The area has an alarm System power is normal System power is missing A fire alarm is active No fire alarm Fire alarm in memory (Turn the area All On and Off to Clear). The existing service or trouble condition has been acknowledged. No service or trouble conditions exist A service or trouble condition is present that has not been acknowledged. The area is turned Part On. The area is not turned Part On. The area is turned off. The area is turned All On or Part On The area is turned All On or Part On The area is turned Off All messages have been read. Message queue is empty An unread message is in the queue. Area is ready to turn on (All On / Part On) Not ready, Zone Open Green LED Red & Green LED On Flashing Flashing Area is off. Area not ready to turn on Installer programming mode is active. Table 5: ICON & LED Indicator Meanings KEYPAD TONES All keypads emit several distinct tones and display text to alert you to system events. The volume of the keypad tones can be adjusted in MENU Type Fire Alarm Tone Burglary Alarm Tone Trouble Tone Key Press Tone Entry Delay Tone Exit Delay Tone Error Tone Menu Mode Chime Tone Meaning When a fire zone sounds an alarm, the keypad will sound 3 seconds on and 2 seconds off (repeat). When a burglary zone activates while your system is turned on, your keypad emits a continuous siren tone. It sounds for the time set by your security company. When a system component is not functioning properly, your keypad sounds 4 fast short beeps followed by a 5 second pause (repeat). Pressing any key on the keypad sounds one short beep, indicating that the key press is accepted. When you enter the premises through a zone programmed for entry delay, the keypad sound a Hi/Low tone to remind you to turn off the area. If the area is not turned off before the entry delay expires, an alarm condition will sound and a report may be sent to your alarm company. After you turn an area All On, the keypad will sound 1 short beep every second. During the last 10 seconds fast short beeps will be heard. If you don t exit before the delay time expires and an exit delay door is faulted, an alarm occurs. If you enter an incorrect value when programming, the keypad will sound a 2 second tone. The keypad will sound a Lo/Hi tone to indicate you have entered MENU Mode and a Hi/Lo tone to indicate you have exited MENU mode. The keypad sounds fast short beeps to alert you when a zone programmed for chime is faulted or unsealled. Table 6: Keypad Tones Red LED On Flashing All On Alarm 2-6

23 Solution-144 Installation Manual Installing the Hardware KEYPAD & READERS SETUP The control panel can have a maximum of 16 keypads and/or readers connected via the LAN terminals. Each keypad or reader must be set to a unique address before they will operate. Each keypad or reader needs to be assigned to a home area via MENU This sets the area the keypad or reader will display and control by default. Keypads and readers can be locked to a home area or allowed to roam or move between areas. At factory default, the home area is factory default to operate Area 1. Set each keypad or reader address using 'Table 7: DIP Switch Address Settings' on page 2-7 and 'Table 8: Rotary Switch Address Settings' on page 2-7 as a guide. i Note Only 1 keypad can be assigned to each address. All keypads are supplied from the factory set to address 1. (OFF-OFF-OFF-OFF). DIP SWITCH ADDRESS SELECT Figure 10: Keypad DIP Switch Address Settings 4 DIP Switch Address Settings Keypad/Reader N o S1 S2 S3 S4 1 Off Off Off Off 2 On Off Off Off 3 Off On Off Off 4 On On Off Off 5 Off Off On Off 6 On Off On Off 7 Off On On Off 8 On On On Off 9 Off Off Off On 10 On Off Off On 11 Off On Off On 12 On On Off On 13 Off Off On On 14 On Off On On 15 Off On On On 16 On On On On Table 7: DIP Switch Address Settings ROTARY SWITCH ADDRESS SELECT Keypads and readers fitted to the system must be assigned a unique address on the LAN. Some keypads and readers include a rotary address switch for quick selection. The following table shows how to set the address setting for each keypad and reader, as well as the number of devices the panel can support. Rotary Switch Address Settings Address Number Keypad/Reader N o Table 8: Rotary Switch Address Settings Figure 11: Rotary Swich Address Settings 2-7

24 Solution-144 Installation Manual Installing the Hardware EOL RESISTOR COLOUR CODE 3K3 = Orange 6K8 = Blue Figure 12: EOL Resistor Colour Chart Selected Resistor Colour Codes Value Band 1 Band 2 Band 3 Band 4 Table 9: 2K2 RED RED RED BROWN 4K7 YELLOW VIOLET RED BROWN 5K6 GREEN BLUE RED BROWN 8K1 GREY BROWN RED BROWN 10K BROWN BLACK ORANGE BROWN 12K BROWN RED ORANGE BROWN 22K RED RED ORANGE BROWN EOL Resisstor Colour Codes Because of variations in the colours used to mark resistors it is recommended that you use a multimeter to verify the value of resistors rather than rely on the colour code. 2-8

25 SECTION 3 Wiring Diagrams ZONE WIRING ZN 1 N/C ZONE 1 using Normally-Open Alarm Contacts you must select Inverted Seal for each zone in MENU A shorted loop is a tamper condition for all EOL zone configurations. GND ZN 2 N/C ZONE 2 2 ZN 1 GND ZN 2 N/O N/O ZONE 1 ZONE 2 Figure 13: N/C No EOL Zone ZN 1 GND ZN 2 ALARM N/C N/C ALARM ZONE 1 ZONE 2 Figure 17: N/O No EOL Zone ZN 1 GND ALARM N/O ZONE 1 Figure 14: N/C Single EOL Zone ZN 2 N/O ALARM ZONE 2 ZN 1 GND ZN 2 N/C ALARM N/C ALARM Figure 15: N/C Split EOL Zone ZONE 1 (3K3 EOL) ZONE 9 (6K8 EOL) Figure 18: N/O Single EOL Zone ZN 1 GND ZN 2 N/O ALARM N/O ALARM ZONE 1 (3K3 EOL) ZONE 9 (6K8 EOL) ZN 1 GND ZN N/C TAMPER TAMPER (6K8 EOL) ALARM N/C ZONE 1 (3K3 EOL) ZN 1 GND Figure 19: N/O Split EOL Zone N/C TAMPER TAMPER (6K8 EOL) ALARM N/O ZONE 1 (3K3 EOL) i Note Figure 16: N/C Zone With Tamper The Above diagrams display the zone wiring configurations using Normally-Closed Alarm contacts and Normally-Open Alarm Contacts. When ZN 2 Figure 20: N/O Zone With Tamper 3-1

26 Solution-144 Installation Manual Wiring Diagrams EOL RESISTOR COLOURS AND VALUES Use either the 4 colour, or solid colour resistors supplied. 3K3 = 6K8 = Orange Blue Figure 21: EOL Resistor Colour Chart BOARD CONNECTORS The following table lists the various sockets, pin headers and switches located on the panel and their functions. Connector Service Tamper Default Voice Module Serial Telco Relay Table 10: Description This socket allow you to connect a service Keypad to the panel during installation. This socket is used to connect the panel enclosure tamper switch. This push button is used to reset the control panel back to factory default. This is used to connect the optional Voice Command Module (CM101B). This socket is used to connect serial devices to the control system like a Serial STU. This is a RJ12 6P/4C connector that allows you to connect the control panel to the PSTN telephone line. The relay select PIN s allow you to easily program the relay common contact to switch either +12v or GND by fitting a plug on link. Board Connector Descriptions TERMINAL DESCRIPTIONS Nº Name Description 1 Earth Earth wire from this terminal is connected to the Mains earth ~ (AC) ~ (AC) BAT (-) BAT (+) +12 V +12 V +12 V GND GND GND LAN + LAN - 14 LAN A 15 LAN B 16 COMM OUT 1 OUT 2 OUT 3 OUT 4 N/C COM N/O Connection of the AC plug pack transformer Negative and positive connections to the stand-by battery. 12 VDC / 7AH These terminals are used to power detectors and LAN devices up to 750 ma. These terminals are used to power LAN devices up to 750 ma. Connect the LAN A data terminal of any LAN device (eg. Keypads, expansion boards) to this terminal. The control panel supports up to 300 m of 24/0.20 (18 AWG) wire on these terminals. Connect the LAN B data terminal of any LAN device (eg. Keypads, expansion boards) to this terminal. The control panel supports up to 300 m of 24/0.20 (18 AWG) wire on these terminals. Alarm power capable of providing a maximum of 2 Amp (+). This terminal is PTC Fuse protected. Programmable output, capable of providing a maximum of 500 ma (-). This terminal is PTC Fuse protected VDC Relay Output - Form C contact 24 INPUT Programmable Input for RF Receivers, Keyswitch and other devices. 25 ZN 1 Zone 1 and 9 sensor loop input (+). 26 GND Common (-) for Zone 1 and 2 sensor loop. 27 ZN 2 Zone 2 and 10 sensor loop input (+). 28 ZN 3 Zone 3 and 11 sensor loop input (+). 29 GND Common (-) for Zone 3 and 4 sensor loop. 30 ZN 4 Zone 4 and 12 sensor loop input (+). 31 ZN 5 Zone 5 and 13 sensor loop input (+). 32 GND Common (-) for Zone 5 and 6 sensor loop. 33 ZN 6 Zone 6 and 14 sensor loop input (+). 34 ZN 7 Zone 7 and 15 sensor loop input (+). 35 GND Common (-) for Zone 7 and 8 sensor loop. 36 ZN 8 Zone 8 and 16 sensor loop input (+) IN IN OUT OUT These terminals are used to connect the telephone line from the street. These terminals are used to connect the premises telephones. Table 11: Terminall Block Descriptions and Functions 3-2

27 LAN OVERVIEW The control panel communicates with other system module devices via the built in RS485 LAN or Local Area Network. For increased security, the system uses anti-substitution technology and a proprietary data encryption algorithm to communicate with all LAN modules. When using the recommended cable types the LAN can be up to 1200 metres in length, or even greater when LAN isolators are used. See the CM797 LAN Isolation Module reference guide for more information on how to use LAN isolators to increase the overall LAN length, improve surge immunity protection and prevent earth loops. i Note It is recommended that one or more CM797 Isolators be used when connecting the LAN between multiple buildings. LAN WIRING Figure 21 and Figure 22 show the two recommended module connection diagrams. The method shown in Figure 21, is only recommended for use where the total LAN length is 300metres or less and the system is not installed in a electrically noisy environment. In this case it is possible to use 7/0.20 or 14/0.20 security cable (non twisted) provided that module voltage levels are maintained within specification. The method shown in Figure 22, offers the greatest immunity to noise interference and voltage surges. This connection method is recommended where the total LAN length is greater than 300metres. When using twisted pair cable the LAN length can be up to 1200metres, and this can be extended even further when using LAN isolators. The LAN can be wired using the daisy chain method as shown, where each module is wired back to the panel on the same cable run or using a star configuration, where individual modules are wired back to the panel on individual wires. Un-shielded cable can be used successfully in many situations however for the highest reliability and performance in areas prone to frequent electrical storms or high levels of electrical interference, shielded twisted pair cable should be used. LAN+ and LAN- should not be used to power detectors or other external devices. These devices should be powered from the +12V terminals on the panel or via an external power supply. When wiring modules with built in power supplies like the control panel and the CM720B Power Supply, do NOT connect the EARTH wire from any 3 wire plug pack to the module s EARTH input terminal, if you have installed a separate communication earth wire. 300 metres max Solution-144 Installation Manual Wiring Diagrams Connect to mains earth via 3 wire plug pack transformer. Security Cable (7/ /0.20) cable can be used for this wiring configuration. The LOOP terminal is not internally connected. It can be used to terminate the LAN+ + on modules which have an on board power supply. Positive LAN voltage is re-generated by the CM720 Power Supply. + - A B A A B B - A B CONTROL PANEL EARTH + - L LAN TERM A Y N A N Fit Shunt B First Device CM704-ZONE EXPANDER EARTH + - A B L A N Y KEYPAD + - A B CM720-POWER SUPPLY LOOP - L A A N B CM710-OUTPUT EXPANDER + - A B L A N EARTH +12V OUT EARTH L A N Y LAN TERM N LAN TERM N LAN TERM Y N Fit Shunt Last Device = +12V OUT = LAN - = LAN + = EARTH = LAN B = LAN A E E Connect to mains earth via 3 wire plug pack transformer. Figure 22: LAN Connection Using 2 Pair Security Cable Recommended for LAN Lengths 300 metres or less. The LAN A and LAN B wires are not interchangeable. Make sure that the LAN A wires from all modules connect to LAN A on the panel and LAN B wires from all modules connect to LAN B on the panel. Do not connect the positives of two power supply sources together. When wiring the LAN to modules that are self powered, or powered from an external source you should terminate the LAN+ into the terminal marked LOOP. This terminal is simply a termination point and is not internally connected. 3-3

28 Solution-144 Installation Manual Wiring Diagrams 1500 metres max Connect to main building earth conductor. * Shield only connected at one end. Belden pair twisted shielded data cable is recommended for this wiring configuration. The LOOP terminal is not internally connected. It can be used to terminate the LAN+ + on modules which have an on board power supply. Positive LAN voltage is re-generated by the CM720 Power Supply. Shield not connected at this end. + - A B A A 2.5mm 2 Yellow/Green CONTROL PANEL C. E. T. EARTH B B - A B 2.5mm 2 2.5mm 2 2.5mm 2 2.5mm A B CM704-ZONE EXPANDER + - A B KEYPAD + - A B CM720-POWER SUPPLY LOOP - A B CM710-OUTPUT EXPANDER + - A B L A N EARTH L A N L A N EARTH L A N +12V OUT EARTH L A N LAN TERM Y N Fit Shunt First Device Y Y Y LAN TERM N LAN TERM N LAN TERM N Last Device = SHIELD = LAN - = LAN + = EARTH = LAN B = LAN A = RE-GENERATED LAN + E E E E NOTE: Do NOT connect plug pack Earth wires to any modules when running a separate communication earth wire. Fit Shunt Figure 23: LAN Connection Using Twisted Pair Cable Recommended for LAN Lengths greater than 300 metres. The LAN- terminals from all modules must be connected together for correct operation. SYSTEM EARTHING When running a CET communications Earth as per Figure 24, the communication earth should be connected to the earth terminal on each module and then connected back through the CET to the main building earth conductor. Do NOT connect the plug pack transformers earth wire to any modules earth terminal. i Note If a separate Communications Earth wire is installed, Do NOT connect the EARTH wire from any 3 wire plug pack to any modules EARTH input terminal. If a separate communications earth is NOT being used, then you should connect the earth wire from the 3 wire plug pack to the panels earth terminal as shown in Figure 22. When using shielded cable, the shield of each length of cable should only be connected to a protective earth at one end. Do no allow the shield to make contact with negative 0 volts, ground or any other wiring within the system. All earth wiring should be carried out in accordance with the local wiring regulations in your area. TERMINATING THE LAN For reliable operation the system LAN must be terminated correctly. The control panel and all LAN modules include a LAN TERM pin header and shunt which is used to connect the termination resistor on the module. When the shunt is installed between the Y pin and the centre pin, the terminator is fitted and when the shunt is between the N pin and the centre pin the terminator is not fitted. Where all modules are connected to the panel on a single cable run, (Daisy Chained) the terminators should be installed on the first and last modules on the LAN. If the modules are connected to the panel via multiple cables all running back to the control panel (Star Configuration) then the terminators should be installed on the modules at the end of the two longest cable runs. There are no LAN terminators on keypads. If a keypad is one of the two furthest devices from the control panel then a 470 ohm 1/2watt resistor can be fitted at the keypad between the LAN A and LAN B terminals. In smaller installations where no LAN modules have been installed there is no need to fit the termination resistor on the control panel. i Note The LAN must be terminated correctly for proper operation. 3-4

Solution 16 plus. Quick Start Guide Security System

Solution 16 plus EN Security System Copyright Notice Unless otherwise indicated, this publication is the copyright of Bosch Security Systems Pty Ltd ( Bosch ). All rights are reserved.you may download

More information

Solution 16 plus. User Guide Security System

Solution 16 plus EN Security System Copyright Notice Unless otherwise indicated, this publication is the copyright of Bosch Security Systems Pty Ltd ( Bosch ). All rights are reserved.you may download

More information

CM705B - Universal Expander Module CM707B - Plug On Zone Expander Security Systems

CM705B - Universal Expander Module CM707B - Plug On Zone Expander Security Systems EN Security System CM705B CM705B - Universal Expander Module The CM705B universal expander provides a cost effective way

More information

Solution 6000 Security Systems

Security Systems EN Security System Copyright Notice Unless otherwise indicated, this publication is the copyright of Bosch Security Systems Pty Ltd ( Bosch ). All rights are reserved.you may download

More information

Solution-16 Operators Manual ISSUE 1.60

Solution-16 Operators Manual ISSUE 1.60 !'#$%&'()*+ Operators Manual Copyright 2002 by, SYDNEY, AUSTRALIA Document Part Number MA880O DOCUMENT ISSUE 1.60 Printed 22 March 2002 This documentation is provided

More information

Control/Communicator Installation Manual

DAS NETWORX NX-8 Control/Communicator Installation Manual Page General Description.. 2 Ordering Information.. 2 Option Definitions.. 2 Programming the LED Code Pads.. 4 Programming the NX-8.. 8 Types

More information

ICP-CC488. Installation Guide ICP-CC488 Control Panel

ICP-CC488 EN Installation Guide ICP-CC488 Control Panel ICP-CC488 Installation Guide Notices EN 2 Copyright Notice Unless otherwise indicated, this publication is the copyright of Bosch Security Systems,

More information

!'#$%&'()**+),-+)).( /'0%1##1%&'(21'$1#( ISSUE 1.40

!'#$%&'()**+),-+)).( /'0%1##1%&'(21'$1#( ISSUE 1.40 MA8XXI 34&0(5167(410(877'(&'9#$:7:(;'

More information

Solution 862 Operators Manual. Issue 1.00

Solution 862 Operators Manual Issue 1.00 Solution 862 Operators Manual Copyright 1998 by Electronics Design and Manufacturing Pty Limited, SYDNEY, AUSTRALIA Document Part Number MA406O Document Issue

More information

ICP-CC488 ICP-CC488 EN. Control Panel. Quick Reference Guide

ICP-CC488 EN Quick Reference Guide ICP-CC488 Control Panel ICP-CC488 Quick Reference Guide Notices EN 2 Copyright Notice Unless otherwise indicated, this publication is the copyright of Bosch Security

More information

VR8. User Guide Intruder Alarm System

VR8 EN User Guide Intruder Alarm System VR8 User Guide Notices EN 2 Copyright Notice Unless otherwise indicated, this publication is the copyright of Bosch Security Systems Pty Ltd ( Bosch ). All rights

More information

Firmware version: 1.10 Issue: 7 AUTODIALER GD30.2. Instruction Manual

Firmware version: 1.10 Issue: 7 AUTODIALER GD30.2 Instruction Manual Firmware version: 2.0.1 Issue: 0.6 Version of the GPRS transmitters configurator: 1.3.6.3 Date of issue: 07.03.2012 TABLE OF CONTENTS

More information

Program Entry Guide. Control Panels

EN Program Entry Guide Control Panels D6412/D4412 Program Entry Guide EN 2 Documentation Conventions Type Styles Used in this Manual To help identify important items in the text, the following type styles

More information

ICP-CC488 ICP-CC488 EN. Control Panel. User s Guide

ICP-CC488 EN User s Guide ICP-CC488 Control Panel ICP-CC488 User's Guide Notices EN 2 Copyright Notice Unless otherwise indicated, this publication is the copyright of Bosch Security Systems, Inc. ( Bosch

More information

Ademco Vista-20P/First Alert FA-168C Basic Commands

Zones 64 total Ademco Vista-20P/First Alert FA-168C Basic Commands Wireless Yes, Zones 09 to 48 + 16 Keyfob Zones (Zones 49 to 64) Batteries Downloadable Partitions 2 12 volt Rechargable inside main Panel, Rhinoceros 3d free download.

More information

User s Information Guide R1A

HSC505-R Home Security Controller - User Manual Release R1a Pi HSC505 and Pi HSC505R Home Security Controller User s Information Guide R1A Page 1 QD Dynamics (Pty) Ltd reserves the right to make changes

More information

CONTENTS QUICK SETUP & INSTALLATION USER MANUAL. SUPA8 Quick Setup & User Manual

SUPA8 Quick Setup & User Manual QUICK SETUP & INSTALLATION CONTENTS FACTORY DEFAULTS.. 1 INSTALLATION OF THE SECURITY SYSTEM.. 2 COMMISSIONING THE DIALLER PANEL.. 5 ZONE INPUT CONNECTIONS.. 7 PANEL

More information

Solution 880 Operators Manual ISSUE 1.10

Solution 880 Operators Manual ISSUE 1.10 Solution 880 Operators Manual Copyright 2001 by, SYDNEY, AUSTRALIA Document Part Number MA408O DOCUMENT ISSUE 1.10 Printed 25 May 2001 This documentation is provided

More information

AC-115 Compact Networked Single Door Controller. Installation and User Manual

AC-115 Compact Networked Single Controller Installation and User Manual December 2007 Table of Contents Table of Contents 1. Introduction..5 1.1 Key Features.. 6 1.2 Technical Specifications.. 7 2.

More information

9452/9453 Installation and User Guide

9452/9453 Installation and User Guide Compatible Equipment 9425 Remote Keypad 9040 Internal Sounder 660 Speech Communicator 8440 4-Channel Minicom 496330 Issue 1 1 of 10 9452/3 Introduction The 9452 and

More information

D24 ALARM CONTROL PANEL USER S MANUAL REVISION 1.1 A$12.00 INC GST

D24 ALARM CONTROL PANEL USER S MANUAL REVISION 1.1 A$12.00 INC GST Ness Security Products Pty Ltd Quality Endorsed Company ISO9001 LIC.No. QEC2074 NSW Head Office only WWW.NESS.COM.AU Australia s largest

More information

TS510 & TS500. Installation & User Guide. Compatible Equipment

Installation & User Guide Compatible Equipment TS510 REM - Remote Keypad 9040 - Loudspeaker DC54/58 - Digital Communicator SD1+ - Speech Dialler 496525 Issue A 1 of 10 TS510 and TS500 Overview Introduction

More information

SECURITY ALARM CONTROL PANEL QUICK SETUP & USER MANUAL

SECURITY ALARM CONTROL PANEL QUICK SETUP & USER MANUAL PINKERTON Quick Setup & User Manual QUICK SETUP & INSTALLATION CONTENTS FACTORY DEFAULTS..1 INSTALLATION OF THE SECURITY SYSTEM..2 COMMISSIONING

More information

CC406. Operators Guide Solution 862

CC406 EN Operators Guide Solution 862 CC406 Operators Guide Notices EN 2 Copyright Notice Unless otherwise indicated, this publication is the copyright of Bosch Security Systems Pty Ltd ( Bosch ). All

More information

ACP10 10 Zone Intruder Alarm System

ACP10 10 Zone Intruder Alarm System Installation Manual Contents 1. System Overview.. 4 System Configuration.. 4 Control Panel.. 4 Remote Keypads.. 5 LED Remote Keypad.. 5 LCD Remote Keypad.. 5 USB-Link..

More information

Control Panel. Solution 2000 / en User's Guide

Control Panel Solution 2000 / 3000 en User's Guide Control Panel Table of Contents en 3 Table of contents 1 Introduction 5 2 Specifications 6 3 Codepad Introduction 7 3.1 Codepad 7 3.2 Codepad Indicators

More information

SPECIAL CONTROL BUTTON FUNCTIONS

Operating Guide 1 2 3 CONTENTS Page No. OPERATING YOUR ALARM 5 General Information 5 Arming the Alarm 5 Disarming the Alarm 6 Arming in Stay Mode 7 Disarming Stay Mode 8 Bypassing Zones 8 Manual Panic,

More information

HONEYWELL COMMERCIAL FIRE/BURG PANEL UL LISTING REQUIREMENTS (Compiled from VistaFBPT Installation Instructions 800-09617V1 Rev A 11/12)

HONEYWELL COMMERCIAL FIRE/BURG PANEL UL LISTING REQUIREMENTS (Compiled from VistaFBPT Installation Instructions 800-09617V1 Rev A 11/12) UL864 (Commercial Fire) Compliance General Requirements The VISTA-128FBPT/VISTA250FBPT

More information

ACTIVE 5 ENGINEERING MANUAL

ACTIVE 5 ENGINEERING MANUAL C & K Systems Ltd C031-066 Issue 3 THE ACTIVE 5 INSTALLATION MANUAL. Date: Feb 1997 INTRODUCTION. The Active 5 is a microprocessor controlled intruder alarm panel. It features

More information

SECTION 13850 DETECTION AND ALARM

SECTION 13850 DETECTION AND ALARM PART 1 GENERAL 1.01 SUMMARY A. Section Includes 1. Control Panel 2 Associated Equipment B. Products Installed But Not Supplied Under This Section 1. Section 16140 - Wiring

More information

INSTALLATION MANUAL PC2525. Version 1.1

INSTALLATION MANUAL PC2525 Version 1.1 TABLE OF CONTENTS FEATURES 1 SPECIFICATIONS 1 INSTALLATION 2 Mounting the Panel.. 2 Mounting the Keypad.. 2 Auxiliary Power Connection.. 2 Bell/Siren Connection..

More information

Challenger Version 8 Basic Alarm System.

Challenger Version 8 Basic Alarm System. This document provides details of the programming requirements for getting a basic alarm system that uses PIN codes to arm/disarm/reset etc., up and running. A

More information

NESS D16. 16 Zone Control Panel and Dialler OWNER S MANUAL

NESS D16 16 Zone Control Panel and Dialler OWNER S MANUAL REVISION 2, JULY 2001 Ness Security Products Pty Ltd Quality Endorsed Company ISO9001 LIC.No. QEC2074 NSW Head Office only WWW.NESS.COM.AU Australia

More information

ADEMCO LYNXR-I Security Systems

K14117 3/06 Rev. A ADEMCO LYNXR-I Security Systems Quick Start Guide UL LYNXR-I is not intended for UL985 Household Fire applications unless a 24-hour backup battery (P/N LYNXRCHKIT-HC or LYNXRCHKIT-SHA)

More information

ABUS WIRELESS ALARM SYSTEM

ABUS WIRELESS ALARM SYSTEM These installation instructions are published by Security-Center GmbH & Co. KG, Linker Kreuthweg 5, D-86444 Affing/Mühlhausen. All rights including translation reserved. Reproductions

More information

Using your LED Plus keypad

Using your LED Plus keypad System 238 System 2316 System 238i System 2316i Part Number 5-051-372-00 Rev B Thank you for purchasing this C&K alarm system Your system is one of the most powerful and advanced

More information

500r+ Installation and User Guide

500r+ Installation and User Guide Compatible Equipment 502rUK-50 Watch/Pendant PA. 509rUK-50 Smoke Detector 515rUK-00 10 metre passive infra red movement detector. 525rUK-00 Remote Set/Unset (Full and

More information

MODEL CA100 REMOTE CONTROL AUTO ALARM SYSTEM INSTALLATION & OPERATION INSTRUCTIONS

MODEL CA100 REMOTE CONTROL AUTO ALARM SYSTEM INSTALLATION & OPERATION INSTRUCTIONS WIRING DIAGRAM Black Antenna Wire 6 Pin 6 Pin Mini Connector Valet Switch Blue LED Indicator Blue Wire: (-) 200mA Unlock

More information

HARDWIRED CONTROL PANELS

USER GUIDE 9651 HARDWIRED CONTROL PANELS Contents 1. Introduction..3 The Alarm System..3 The Keypad..3 About This Guide..5 2. Everyday Operation..6 How Do I Know if the System is Working?..6 Setting

More information

TABLE OF CONTENTS FEATURES

TABLE OF CONTENTS FEATURES 2 Keypad Programmable.. 2 EEPROM Memory.. 2 Static/Lightning Protection.. 2 Supervision.. 2 Operation.. 2 SPECIFICATIONS 2 PC1550 Control Panel.. 2 PC1500RK Keypad.. 2

More information

SCORPION Z16040C Alarm Controller User Instructions

SCORPION Z16040C Alarm Controller User Instructions Thank you for choosing to purchase this micron security alarm controller. Micron product is manufactured to exacting quality standards. We understand

More information

IDS. Users Guide to Keypad Functions S E C U R I T Y MANUAL NO. 700-171-01B ISSUED AUG 2002 VERSION 1.18

INHEP DIGITAL IDS S E C U R I T Y Users Guide to Keypad Functions MANUAL NO. 700-171-01B ISSUED AUG 2002 VERSION 1.18 Summary of Operation A rm/ disarm [#] + [USER CODE] Quick Quick Quick Away Arm Stay

More information

GSM AD05 Slave GSM Auto Dialer- Instruction Manual

GSM AD05 Slave GSM Auto Dialer- Instruction Manual Please read these instructions before you start the installation Features LCD display Programmable 9 x 32 digit phone numbers for each trigger. 10 second

More information

CAD-05 Kit GSM Auto Dialer. Owner s Manual

CAD-05 Kit GSM Auto Dialer Owner s Manual CAD-05 Kit Manual.indd 1 Warnings: This device complies with Part 15 of the FCC rules, Operation of this device is subject to the following conditions: 1. This

More information

Elvey is a leading distributor of electronic security equipment in Africa. Our vision is to assist in the protection of people and property by

Elvey is a leading distributor of electronic security equipment in Africa. Our vision is to assist in the protection of people and property by providing quality, innovative products and solutions to the

More information

INSTALLATION GUIDE. Card Reader & Controller with KIM Swipe Reader for Solitaire 850 / 950 / 850L Learnlok PK2930

INSTALLATION GUIDE Card Reader & Controller with KIM Swipe Reader for Solitaire 850 / 950 / 850L Learnlok PK2930 Card Reader and Controller Model 3.5 with KIM Swipe Reader Table of Contents 1. Features.................

More information

WITURA CORPORATION SDN BHD

WT 1010SA Stand Alone GSM Alarm System User Manual and Installation Instructions Version: 1.2 Updated: 4 JAN 2012 WITURA CORPORATION SDN BHD Stand Alone GSM Alarm System Instruction Manual 1 Introduction:

More information

Crow Limited Warranty. Print Version 017

Crow Limited Warranty (Crow) warrants this product to be free from defects in materials and workmanship under normal use and service for a period of one year from the last day of the week and year whose

More information

Solution-16 Operators Manual ISSUE 1.40

Solution-16 Operators Manual ISSUE 1.40 Solution-16 Operators Manual Copyright 1995-97 by, SYDNEY, AUSTRALIA Document Part Number MA880O Document Issue 1.40 Printed 29 July 1997 This documentation is

More information

GJD HYL005. Please read these instructions before you start the installation. Installation. GSM Autodialer Instruction Manual

GJD HYL005 GSM Autodialer Instruction Manual Please read these instructions before you start the installation Features: LCD display. Programmable 9 x 32 digit phone numbers for each trigger. 10 second

More information

ICP-CC404 ICP-CC404 EN. Control Panel. User s Guide

ICP-CC404 EN User s Guide ICP-CC404 Control Panel ICP-CC404 User's Guide Copyright Notice Copyright Notice Unless otherwise indicated, this publication is the copyright of Bosch Security Systems, Inc.

More information

NetworX Series. NX- 4/8 Code Pad. User Manual (Australian Version)

NetworX Series NX- 4/8 Code Pad User Manual (Australian Version) Table Of Contents Code Pad Diagram.. Inside Front Glossary of Terms..2 Understanding the Code Pad lights..3 Code Pad Tones..4 Fully

More information

SCORPION. micron security products

SCORPION 4120 6020 & 8020 USER INSTRUCTIONS Thank you for purchasing a Quality Micron Security Alarm Controller. Micron product is manufactured to exacting quality standards. We understand the importance

More information

Solution 144 The Integrated Access Control & Alarm System made for your business

Solution 144 Access Control & Alarm System 1 Solution 144 The Integrated Access Control & Alarm System made for your business The Solution 144 Integrated Access Control & Alarm System offers an extensive

More information

Reference & Installation Manual

& Versions 4.4 (728ULT) & 4.1 (738ULT) 728ULT 738ULT Reference & Installation Manual Table of Contents Introduction.. 1 About This Manual.. 1 New Features.. 1 Main Features.. 1 Specifications.. 1

More information

CAPTAIN 6. USER GUIDE System ver. 6.0. 6 Zones Intruder Alarm System. PIMA Electronic Systems Ltd. www.pima-alarms.com

CAPTAIN 6 6 Zones Intruder Alarm System USER GUIDE System ver. 6.0 PIMA Electronic Systems Ltd. www.pima-alarms.com P/N 4410049, G2 XX en, Jan. 2010 2 CAPTAIN 6 User Guide SAFETY INSTRUCTIONS Your CAPTAIN-i

More information

i 70 Installation Manual V1.04 Contents Grade 2 Wireless Intruder Alarm System YOUR SECURITY IS OUR PRIORITY Installation Instructions 2

YOUR SECURITY IS OUR PRIORITY Contents Installation Instructions 2 Operation Instructions Trouble shooting Technical Specification 8 25 31 i 70 Grade 2 Wireless Intruder Alarm System Global Security Devices

More information

astec Integrated Alarm System USER GUIDE

astec Integrated Alarm System USER GUIDE 020008599 CONTENTS Full Set, Part Set and Disarm 3 Instant Full Set 3 Part Set with exit time 4 Bell Test 4 Bypassing zones 4 Switch Lights on/off 4 Bypass (24

More information

Auto Dialer. Manual E-921APQ E-921GPQ

Troubleshooting: Auto dialer will not arm/disarm Auto dialer will not dial out Unit doesn t respond to a call-back Difficulty in activating room monitor by telephone remote control Make sure that you have

More information

Installation & Programming Guide. ELITE 64 Version. 64 Zone Wired/Wireless Control/Communicator Arrowhead Alarm Products Ltd

ELITE 64 Version 2 64 Zone Wired/Wireless Control/Communicator Arrowhead Alarm Products Ltd Installation & Programming Guide Proudly Designed and Manufactured in New Zealand Arrowhead Alarm Products Ltd

More information

Meridian 8 and Meridian 16 Broadband Alarms

Meridian 8 and Meridian 16 Broadband Alarms User Manual Micron Security Products Ltd November 2014 1 Table of Contents About the Meridian Broadband Alarm.. 3 Ethernet Connection Diagram.. 4 Meridian

More information

Understanding the Code Pad lights..4. Code Pad tones..5. Fully arming the system On MODE..6. Fully arming the system - Quick Arm MODE..

TABLE OF CONTENTS..Glossary of terms..2..code Pad Diagram..3 Understanding the Code Pad lights..4 Code Pad tones..5 Fully arming the system On MODE..6 Fully arming the system - Quick Arm MODE..6

More information

HUNTER-PRO 32 Ver. 3.8 Intruder Alarm System RXN-9/416 User Guide

HUNTER-PRO 32 Ver. 3.8 Intruder Alarm System RXN-9/416 User Guide PIMA Electronic Systems Ltd. 5 Hatzoref Street, Holon 58856, Israel +972-3-5587722 +972-3-5500442 support@pima-alarms.com http://www.pima-alarms.com

More information

Microprocessor Home Security System

numbers of sensor s activations in the zone and after which activations the zone will be discarded (ignored). On every system s arming the counter is cleared in self. 6.3.11. 2 - Triger Timer - enter a

More information

HAM841K ALARM CONTROL PANEL FOR COMMERCIAL AND RESIDENTIAL SECURITY SYSTEMS

ALARM CONTROL PANEL FOR COMMERCIAL AND RESIDENTIAL SECURITY SYSTEMS USER MANUAL USER MANUAL ALARM CONTROL PANEL FOR COMMERCIAL AND RESIDENTIAL SECURITY SYSTEMS INTRODUCTION The (HA-841K) is a complete

More information

TS590. Intruder Alarm Control Panel. SYSTEM OPEN 17:30 01 Jan ENT 0 ESC

TS590 Intruder Alarm Control Panel 7:0 0 Jan _ ~ A B 5 6 C 7 8 9 D 0 ESC Setting the System Enter your passcode XXXX then leave the protected area. Unsetting the System Go directly to the keypad and en

More information

HILLS Series LED Code Pad User Manual

HILLS Series LED Code Pad User Manual Not all features may be available on your system Check with your installer to find out which features are programmed Page 2 TABLE OF CONTENTS Code Pad Diagrams..2

More information

ICP-CP500. User's Guide ICP-CP500 Codepads

ICP-CP500 EN User's Guide ICP-CP500 Codepads ICP-CP500 User's Guide 1.0 ICP-CP500 Series Codepads Overview EN 2 1.0 ICP-CP500 Series Codepads Overview The codepad is the communications interface between

More information

Solution-8 Control Panel

Solution-8 Control Panel Issue 3c September 1994 Copyright 1994-1995 All rights reserv (MA 800 O) Important Note As there are many different types of consoles available for use with this control panel,

More information

TABLE OF CONTENTS FEATURES 2 SPECIFICATIONS 2

TABLE OF CONTENTS FEATURES 2 SPECIFICATIONS 2 INSTALLATION 3 Mounting the Panel.. 3 Mounting the Keypad.. 3 Auxiliary Power Connection.. 3 PGM Terminal Connections.. 3 Bell/Siren Connection.. 3 Keypad

More information

NX-8 Installation manual Page 1 Date 13/03/04

NetworX NX-8 Installation Manual NX-8 Installation manual Page 1 Date 13/03/04 CONTENTS CONTENTS..2 GENERAL INFORMATION..4 ORDERING INFORMATION..4 FEATURE DEFINITIONS..5 PROGRAMMING THE NX-8 KEYPADS..12

More information

AUTODIALLER / QUICKDIALLER - SA132

AUTODIALLER / QUICKDIALLER - SA132 INSTRUCTION LEAFLET ENGLISH www.thermomax-group.com CONTENTS 1 SETUP AT A GLANCE.. 2 2 FOREWORD.... 3 3 INSTALLATION... 4 4 KEYPAD AND INDICATORS... 5 SETTING

More information

IDS X-Series User Manual 700-398-01D Issued July 2012

1 2 Contents 1. Introduction to the IDS X-Series Panels.. 7 2. Before Operating Your Alarm System.. 7 3. Understanding the Keypad LEDs.. 8 3.1 Viewing Data on an LED Keypad.. 12 3.1.1 LED Status Indicators..

More information

NetworX NX-8 Control/Communicator Installation Manual

NetworX NX- Control/Communicator Installation Manual Table of Contents General Description.. Ordering Information.. Feature Definitions.. - Programming the LED Keypads.. Programming the NX-.. 9- Types

More information

CONTENTS 4. HOW TO UNSET THE PANEL..7

Pi-8 USER MANUAL CONTENTS 1. THE KEYPAD AND ITS OPERATION..3 1.1 DESCRIPTION OF THE KEYPAD LEDS.. 3 1.1.1 READY LED (RED)..3 1.1.2 TAMPER LED (RED)..3 1.1.3 POWER LED (GREEN)..3 1.1.4 CIRCUIT LEDs

More information

Users Guide to Keypad Functions

Warn Winch Vr8 Installation Guide

Users Guide to Keypad Functions MANUAL NO. 700-175-01J ISSUED JAN 2002 VERSION 1.41 Summary of Operation A rm/ disarm [#] + [USER CODE] Quick Quick Quick Panic Fire Medical Away Arm Stay Arm Stay Arm &

More information

Master User Guide Premier Elite 24/48/88/168/640

Master User Guide Premier Elite 24/48/88/168/640 INS177-7 Overview Premier Elite Series Master User Guide Contents 1. Overview.. 4 Introduction.. 4 Keypads.. 6 Emergency Keys.. 7 The Quick Arm Keys..

More information

APR-PRT3 Printer Module: C-Bus Programming Instructions

APR-PRT3 Printer Module: C-Bus Programming Instructions We hope this product performs to your complete satisfaction. Should you have any questions or comments, please visit www.paradox.com and send us

More information

SECURITY SYSTEM NOTES. EMERGENCY ACTIVATION KEYS (check if enabled) PROGRAMMED FUNCTIONS

SECURITY SYSTEM NOTES Installing/Service Company For Service Call Installation Date / / Central Station Duress Code EMERGENCY ACTIVATION KEYS (check if enabled) Fire Auxiliary Emergency Police PROGRAMMED

More information

HILLS Series LED Code Pad User Manual

Software Installation Manual

HILLS Series LED Code Pad User Manual Not all features may be available on your system Check with your installer to find out which features are programmed Page 2 TABLE OF CONTENTS Code Pad Diagrams..2

Installation Guide

More information

PK5500 v1.1 Installation Instructions

PK5500 v1.1 Installation Instructions 1 2 3 4 5 6 7 8 9 * 0 # WARNING: Please refer to the System Installation Manual for information on limitations regarding product use and function and information on

More information

XP-600 Programming Instructions

Hexadecimal Data Entry To Enter a hexadecimal digit enter the following A= A1 D= A4 B= A2 E= A5 C= A3 F= A6 XP-600 Programming Instructions Note These Programming Instructions are intended to be used in

More information

Elite 8D/Lite Version 8 Zone Controller. Arrowhead Alarm Products Ltd. Operating Guide. Proudly Designed and Manufactured in New Zealand

Elite 8D/Lite Version 8 Zone Controller 8 Arrowhead Alarm Products Ltd Operating Guide 1 Proudly Designed and Manufactured in New Zealand 2 CONTENTS Page No. INTRODUCTION 4 About your Alarm 4 OPERATING

More information

MAKING MODERN LIVING POSSIBLE. AK-SC255 On-Site Installation Guide DANFOSS ELECTRONIC CONTROLS & SENSORS

MAKING MODERN LIVING POSSIBLE AK-SC255 On-Site Installation Guide DANFOSS ELECTRONIC CONTROLS & SENSORS How to Use This Guide Read this Guide completely as you install and start up your new AK-SC 255 controller.

More information

User Manual GSM Alarm System. www.deltasecurity.cn. All rights reserved by Delta Security Co., Ltd

User Manual GSM Alarm System All rights reserved by Delta Security Co., Ltd Dear Clients, Thank you for using our GSM Alarm System. We are committed to giving you the best home security available today

More information

tattletale User Guide Consumer unit version 2.48 1 P a g e

tattletale User Guide Consumer unit version 2.48 1 P a g e Contents Basic 1.. 4 Base Unit Features.. 4 Initial Setup.. 4 Arming.. 5 Disarming.. 5 Quiet Button.. 5 Settings.. 5 Settings 2.. 6 Quick

More information

Security System User Guide

Security System User Guide Contents 1. Introduction.. 1 Controls and Displays.. 3 Displays.. 3 Controls:.. 4 2. Everyday Operation.. 5 Access to the System.. 5 Entering and Leaving the Protected

More information

Magellan All-in-one Wireless Security System

Magellan All-in-one Wireless Security System MG6250 Console Version 1.0 Menu Programming Guide Introduction The MG6250 All-in-one Wireless Console is a two-partition, 64-zone wireless console, offering

More information

Memcom Emergency Telephone

Memcom Emergency Telephone Installation Guide Ref No. 450 900 (GB) Version 2 + + Simple wiring for quick installation + + Integrated LCD display shows you what you have programmed + + All code based programming

More information

Contact ID as of 2/2/2015

Contact ID as of 2/2/2015 100 Medical Zone A non-specific medical exists 101 Personal Emergency Zone Emergency Assistance request 102 Fail to report in Zone A user has failed to activate a monitoring device

More information

ELECTRONIC ENGINEERING LTD. FREEWAVE Zone Wireless Control Panel. Installation and Programming Guide

ELECTRONIC ENGINEERING LTD. FREEWAVE 64 64 Zone Wireless Control Panel Installation and Programming Guide P/N 7111380 Rev. F N.A Version 1.11 102005 Copyright by Crow Products Ltd November 2005 FreeWave

More information

NetworX NX-6V2. LED Keypad User Manual

NetworX NX-6V2 LED Keypad User Manual POWER Light is on when AC power is present; flashes to indicate a low battery condition. ARMED Light is on when armed; off when disarmed; flashes to indicate a previous

Compaq armada e500 laptop. SoftPaqs for Microsoft Windows 98 (continued) Family Driver/Enhancement Sequence SoftPaq # E500 System Enhancements First SP13849 ATI Rage Pro Video Driver Second SP12698 Audio Driver (M2E) Third SP12396 Power Management Fourth SP12668 Power Management Enhancements Fifth SP11335 MultiBay. Note: If you did not upgrade over Microsoft Windows 98 along with the Compaq System Enhancements Disk, you will have one or more unknown devices shown in the Device Manager. • HITE APER (cont.) Table 1. These are cosmetic in nature and do not degrade performance in any way.

More information

Galaxy 2 Series. User Guide. Honeywell Security

Galaxy 2 Series User Guide Honeywell Security Table of Contents Table of Contents.. iii Introduction..1 Controlling Your Alarm System..2 Users.. 2 Groups.. 2 Keypads..3 Prox Tags/Cards.. 3 Wireless

More information

First Alert FA140C/142C Installer Notes M. Leuck

First Alert FA140C/142C Installer Notes M. Leuck 1. Programming can only be done by 6139 Alpha keypads, standard 6128 keypad cannot be used to program zones 2. Program new Master Code in section *20 (old

More information

DC-8706K Auto Dial Alarm System

DC-8706K Auto Dial Alarm System User Guide Basic Contents: 1x the host unit; 1x wireless door (window) magnet; 1x wireless infrared detector; 2x remote control; 1x siren; 1x phone core; 1x AC to DC power

More information

GEM-P801 Programming Instructions

NOTE After 15 minutes of keypad inactivity the keypad will emit a steady tone indicating the panel has been left in Dealer Program Mode. Enter Dealer Code to exit or press the C key to return to Dealer

More information

PRT3 Printer Module: ASCII Protocol Programming Instructions

PRT3 Printer Module: ASCII Protocol Programming Instructions We hope this product performs to your complete satisfaction. Should you have any questions or comments, please visit www.paradox.com and send

More information

GSM Autodialer Professional GJD700 Speech & Text Autodialer

Text Edit message GSM Autodialer Professional GJD700 Speech & Text Autodialer Introduction The GSM Autodialer Professional works in conjunction with standard alarm systems and makes use of your preferred

More information

DORMA MODEL PS-406BB POWER SUPPLY INSTALLATION INSTRUCTIONS

Features: INSTALLATION Install in accordance with NFPA 70. DORMA MODEL PS-406BB POWER SUPPLY INSTALLATION INSTRUCTIONS Up to 1.95 Amps Load Capacity Class 2 Rated Outputs Overload, Over Voltage, and Short

More information

Control Panels D9412GV4/D7412GV4/D7212GV4. Owner's Manual Supplement

Control Panels D9412GV4/D7412GV4/D7212GV4 en Owner's Manual Supplement System Requirements Minimum system requirements for Classification in accordance with ANSI/SIA CP-01-2007: UL Listed and Classified

More information